LED indicator Stealth II, tinted glas, e-marked

Model specific indicator adapter acble for Yamaha Tenere 700. This adapter cable is needed to connect aftermarket indicator with 3.5mm round plugs to the Yamaha system connectors. So no extra welding or crimping of connectors necessary. Price per Pair Fits all: Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rally up to 2022 (without  factory LED indicators)   Does not fit 2023 onwards models with OEM mounted LED indicator!

Small, but very usefull rubber cover for flasher ends with M8 threat. If turn signals are bolt to e.g. a license plate holder, the thread and nut of the turn signal is often visible. The rubber cover not only eliminates this optical flaw, it also prevents from too much dirt on the thread. Suitable for all turn signals with M8 thread. Price per set with 4 pieces.

Frequency stabilised flasher relay for LED indicators with load range from 0.1-100 watts   Especially when you have problems with the dash board lights this relay is be the solution. Water and shock resistant, for use with combination of standart 21w and LED indicators or only with LED indicators. Works also on bikes with hazard indicators! You only need 1 relais for 1 bike - doesn't matter is you have 2 or 4 new indicators. Additional ground connetion wire.   Fits e g.:   Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rally up to 2022 (without  factory LED indicators) Yamaha XT-660R/X Yamaha XT660Z Yamaha XT-660ZA Tenere ABS Yamaha XT-1200Z Yamaha XT-1200ZE Yamaha MT-03 Yamaha MT-07 .....

Frequency stabilised flasher relay for LED indicators with a switching capacity of 0.1-100 watts.   Water and shock resistant, for use with combination of standart 21w and LED indicators or only with LED indicators. Works also on bikes with hazard indicators! You only need 1 relay for 1 bike - doesn't matter is you have 2 or 4 new indicators.   Please note: This relay has a switching capacity of 0,1-100 watts. In newer vehicles, the power consumption of 4 turn signals can be much less than 1 watt. Especially if an LED for the turn signal indicator is used in the dash board as well, the cockpit LED might not "flash". In this case, the LED for the turn signal indicator does not work correctly. Please install a resistor on one of the right or left hand indicators. Also the relay with part number EL-BLR-4P provides a reliable remedy. No additional resistors needed. EL-BLR-4P is our recommendation to use e.g. with Yamaha Tenere 700 (up to year 2022). Newer models does not have indicator relais anymore)   Fits e g.:   Yamaha XT-660R/X Yamaha XT660Z Yamaha XT-660ZA Tenere ABS Yamaha XT-1200Z Yamaha XT-1200ZE Yamaha MT-03 Yamaha MT-07 Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rall up to 2022 (without  factory LED indicators) etc...

Why are installing load resistors necessary for LED turn signal lights? Resistors for LED indicator, which have a much lower power consumtion compared to standart 21w indicators. If you don't install load resistors (also known as equalizers) with LED turn signal bulbs, you will experience the notorious hyper flash issue. Hyper flash is exactly what it sounds like, where the turn signal light flashes rapidly and is almost headache inducing. Not only is this ugly, but you may also attract the police who think your bulb is burned out. Just connect the resistors between the indicators and the wiring harness. Delivered as a set for 2 indicators. For the Yamaha XT-660 models as an alternative also an electronic flasher relais can be used. Resistors avaiable in two load values: · 27 Ohms / 5 Watt · 6.8 Ohms / 25 Watt (for bikes with warning flashers like e.g. XT-660, XT-1200Z)