Indicator Adapter for aftermarket Yamaha Tenere 700

Small, but very usefull rubber cover for flasher ends with M8 threat. If turn signals are bolt to e.g. a license plate holder, the thread and nut of the turn signal is often visible. The rubber cover not only eliminates this optical flaw, it also prevents from too much dirt on the thread. Suitable for all turn signals with M8 thread. Price per set with 4 pieces.

LED indicator Slight with newest SMD Technology New look with glas in front and rear direction. Flashing to the front direction very bright, to the rear darker. LED in orange colour. The measurements of this indicator are only approx. 45 x 10 mm! Extremely small but very bright! The overall length of the indicator (without threat) is about only 60 mm. E-marked for front and rear use. Newest SMD LED technology for your safety. Avaiable in black or stylish blue, red or white! Depending on the model you might need a pair of resistors or an LED flasher relais! See accessories. · newest SMD Technology · Meassurments: 45x10mm · Length about 60mm · street legal · avaible in different colours · Price per pair

The current highlight amongst the LED indicators now avaiable. Strong 'SPEAR' look with tinted glas. Latest LED technology with very bright orange light for a safety plus. Small but very bright light. E-marked for front and rear use. Sold as a pair for front or rear use. · Material: plastic, black, glas tinted · perfect look for your bike · 2 indicators per set · Dimension approx.: L: 51 x W: 25 x H: 23mm · needed flasher relais or resistors to be ordered seperately · easy to fit

The latest LED indicator highlight! Angular stealth look in clear glass design. Clear cover glass, LEDs illuminated in orange, indicator tip with a stylish orange design. The dimensions of the turn signal head are just 45 x 25 mm! Very small and super bright. A 1-euro piece for comparison in the picture.   The total length of the indicator, without thread, is approx. only 60 mm. The turn signals are E-approved for front and rear.   current, bright LED technology for added safety plastic, black, glass smoked grey optically perfectly matching turn signals approx. dimensions: L: 45 x D: 25 x H: 15mm price per pair   Depending on the motorbike model, either a pair of resistors or a new, electronically controlled, load-independent flasher relay is additionally required! See accessories.

The LED indicator Stealth is now avaible in the even smaller Stealth II version! Sharp 'Stealth' look with clear lens design. Cover glass clear, LED glow in orange. Measures of the indicator head only approx. 29x18mm! Extremly small but very bright light. The indicators are E-appoved, for use the front and rear. Sold as a per pair.

High-quality SMD LED indicator in a black aluminium housing.   Ultrabright SMD LEDs! 5 powerful SMDs make sure you have an unbeatable bright flash light. Very precisely made - 100% dust and waterproof. No problems with humidity! Future design with smoke grey glass and orange LEDs. The measurements of the indicator head are only 35x12 mm! Extremely small but brighter than a lot of other, much bigger indicators. Also avaiable as an indicator/tail/brake light combination E-marked for front and rear use. Price for a pair.   Measurements:   Length 44 mm x Height 13 mm  x Deepth 15,5 mm (including lens) Rubber arm: D. 13 mm, L. 11 mm Bolt M8 x 1.25 mm, Length ~ 20 mm   Depending on the bike you might need a pair of resistors or a new electric LED flasher relais. See accessories

High-quality LED indicator or indicator/tail/brake light combination in a black aluminium housing. Ultrabright SMD LEDs! 3 ultra powerful SMDs enable the indicator in a very small housing. Very precisely made - 100% dust and waterproof. No problems with humidity! Future design with clear glass and orange LEDs. The measurements of the indicator head are only 32x12 mm! Extremely small but brighter than a lot of other, much bigger indicators. Avaiable as indicator or indicator/tail/brake light combination E-marked for front and rear use. Price for a pair. Measurements: A: 32 mm B: 45 mm C: 11 mm Bolt threat M8 x 1.25 mm, Length ~20 mm. Depending on the bike you might need a pair of resistors or a new electric LED flasher relais. See accessories  

Frequency stabilised flasher relay for LED indicators with load range from 0.1-100 watts   Especially when you have problems with the dash board lights this relay is be the solution. Water and shock resistant, for use with combination of standart 21w and LED indicators or only with LED indicators. Works also on bikes with hazard indicators! You only need 1 relais for 1 bike - doesn't matter is you have 2 or 4 new indicators. Additional ground connetion wire.   Fits e g.:   Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rally up to 2022 (without  factory LED indicators) Yamaha XT-660R/X Yamaha XT660Z Yamaha XT-660ZA Tenere ABS Yamaha XT-1200Z Yamaha XT-1200ZE Yamaha MT-03 Yamaha MT-07 .....

Tail tidy kit with free adjustable number plate holder for the Yamaha Tenere 700   The adjustable angle of inclination and the adjustable indicator holders allow a variety of mounting options. The original number plate / indicator holder is equipped with a splash guard or number plate holder that extends far downwards. This not only looks unsightly but also tends to break off in off-road use. No sawing, bending, drilling on the original parts while installing out tail tidy kit- everything is supplied ready for installation. The filigree holder in high-quality aluminium-steel combination with black powder-coated or anodised finish has been specially developed for the Tenere 700, is robust, weather-resistant and will withstand harshest conditions. The indicator adapters can be adjusted in width (175-210 mm) and fixed in three positions. The angle of inclination is continuously adjustable via slotted holes. Number plate holder made of laser-cut and CNC-bent aluminium. All parts are black plastic-coated or with black anodised finish for long-lasting surface quality. Delivery includes high-quality LED number plate lighting with elegant and clean cable routing and indicator adapters for aftermarket turn signals with M8 thread. Alternatively OEM Yamaha turn signals adapters (oval shaped opening) can be found in the accessories below.   The Tenere 700 benefits immensely visually from this sporty rear end. It makes the motorbike as a whole appear much lighter and sportier.   Details:   Adjustable licence plate holder made of laser-cut aluminium and steel. Adjustable indicator position Width of licence plate area: 180 mm Incl. licence plate holder and licence plate light Material: aluminium, powder-coated Licence plate light - E-approved No original parts have to be changed or destroyed! Rebuilding to the original parts is possible at any time. Compatible with the high HP Corse and MIVV Rallye silencer. Come swith adapters for aftermarket turn signals with M8 / M10 thread. Shown Indicators / Reflector / Reflector and bracket not included - please order separately if required. See accessories for the World Raid Model the seperate sold OEM indicator adapters are needed - see accessories   Fits for all :   Yamaha Tenere 700 2019 onwards Yamaha Tenere 700 Rally 2020 - 2022